HV500/HV1900 & HV3000 Accessories

Spare spray gun for HVLP 500/1900/3000
Part # L0242
For HVLP 500 and HVLP 3000 Series
Includes spray gun with One (1) Quart Paint Pot
Includes standard 2.0 mm (0.08 in.) brass needle and fluid tip
Good to have a spare if painting a variety of jobs or different colors on the same job

 

1.0 mm Brass Needle for HVLP 500/1900/3000
Part # HVACC10R
Needle Tip Size 1.0 mm (0.04 in.)
Ideal for an ultra fine finish and thin viscosity materials, especially water based finishes.

 

1.5 mm Brass Needle for HVLP 500/1900/3000
Part # HVACC15R
Needle Tip Size 1.5 mm (0.06 in.)
Ideal for a fine finish and thin/medium viscosity materials.

 

2.0 mm Brass Needle for HVLP 500/1900/3000
Part # HVACC20R
Needle Tip Size 2.0 mm (0.08 in.)
Ideal for a quality finish and medium/thick viscosity materials.

 

2.5 mm Brass Needle for HVLP 500/1900/3000
Part # HVACC25R
Needle Tip Size 2.5 mm (0.10 in.)
Ideal for a coarse finish and thin to thick viscosity materials.

 

Spare Paint Pot for HV500/HV1900/HV3000 spray gun
Part # HVACC3FD
For HV500 and HV3000 Spray Gun
One (1) quart capacity
Ideal spare if painting a variety of jobs
Allows storing pre-mixed paint in greater volumes
Allows storing different colored paints
Allows storing unused paint while spraying another job

 

HVLP Spray Gun Cleaning Kit for All HVLPs
Part # SGCK1
For ALL HVLP Series Spray Stations Guns
Assures Preventive Maintenance for Longer Life
Comes With Five (5) Brushes and Two (2) Nozzle Cleaners for Fast, Efficient Clean-up
Assures Perfect Performance Every Time

 

HVLP Viscosity Cup for All HVLPs
Part # SG243
For ALL HVLP Series Spray Stations Guns
The viscosity cup is used to indicate if a product is thin or thick. Materials should be tested before spraying to see if thinning is required. The correct viscosity is important to ensure the paint atomizes correctly and sprays evenly.

 

What Needle Do I Need?
Generally, it is important that you match your needle tip size to the paint type being used, the thickness of the paint and the desired quality of finish. A correct match will ensure a more satisfying result, a better painting experience, a quality job and savings in paint and time.

For example, for a finish using a polyurethane or varnish with thinner viscosities, a finer needle tip size would be more suitable since it would atomize the paint to a much finer mist and apply a lighter coat.

Selecting the Needle Kit
The Earlex Spray Station 500, 3000 and 5000 Series all come standard with a 2.0 mm (0.08 in.) diameter needle and fluid tip. The standard tip is the most versatile and can be used with a wide range of paints. Optional needle sizes available range from 1.0 to 2.5 mm (0.04 in. to 0.10 in.). These are described below.

In general, larger diameter needles and fluid tips are ideal for higher viscosity materials since they allow thicker materials to be sprayed where finish is not of paramount importance. Smaller diameter needles, in contrast, are more suitable for lower viscosity materials ensuring a higher quality finish.

Check your instruction manual (can be downloaded from this web site) for information on selecting the correct spray pattern, paint volume, spraying technique and maintenance tips.

Needle Selection Guidelines

Needle Fluid Tip SizeMaterial Sprayed
  
1. 0 to 1. 5 mmCellulose, Acrylics, Synthetics, Polyurethane, Thinner
  
(0.04 to 0.06 in.)Lacquers, Fluorescent, Oil-Based Stains
  
1.5 to 2.0 mm (0.06 to 0.08 in.)Oil base, Hammer, Oxide, Primer, Air Drying, Enamel, Varnish, Marine Paint, Multi-Color, industrial Synthetics, Oil, Polyurethane, Aluminum Thicker Lacquers, Water-Based Stains, Shellac
  
2.0 to 2.5 mm (0.08 to 0.10 in.) Chlorinated Rubber, Oxide, Zinc Rich Primer, Epoxy, Plastic Additives, Floor Paving Paint, Latex
Ideal Viscosity
  
Water Based Paint & Latex
  
45 to 60 seconds Varnish - Follow manufacturer's guidelines
  
Oil Based Paint
45 to 50 seconds
Wood Stain - Follow manufacturer's guidelines
  
Wood Preservatives
No dilution
Cellulose - Follow manufacturer's guidelines
  
PrimerFollow manufacturer's guidelines

The HVLP Spray Station 500 Series is recommended for use with products having a viscosity of up to 45 seconds; Spray Station 3000 and 5000 Series with a viscosity of up to 60 seconds. Making the paint too thin may lead to extra coats which may not be necessary for the finish you require. However, if you require a high quality finish, then more lighter coats will be beneficial.

 

Didn't find what you were looking for?

Contact us

Cell: 416 347 9222

Email: dfines@rogers.com

8:00 a.m.-6:00 p.m.
Monday to Friday

 

Download Accessory page by clicking here.....